GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)
This commit is contained in:
@@ -0,0 +1,360 @@
|
||||
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
|
||||
/*
|
||||
* Copyright (C) STMicroelectronics 2017 - All Rights Reserved
|
||||
* Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
|
||||
*/
|
||||
/dts-v1/;
|
||||
|
||||
#include "stm32mp157c-ed1.dts"
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
|
||||
/ {
|
||||
model = "STMicroelectronics STM32MP157C eval daughter on eval mother";
|
||||
compatible = "st,stm32mp157c-ev1", "st,stm32mp157c-ed1", "st,stm32mp157";
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
aliases {
|
||||
serial0 = &uart4;
|
||||
ethernet0 = ðernet0;
|
||||
};
|
||||
|
||||
clocks {
|
||||
clk_ext_camera: clk-ext-camera {
|
||||
#clock-cells = <0>;
|
||||
compatible = "fixed-clock";
|
||||
clock-frequency = <24000000>;
|
||||
};
|
||||
};
|
||||
|
||||
joystick {
|
||||
compatible = "gpio-keys";
|
||||
#size-cells = <0>;
|
||||
pinctrl-0 = <&joystick_pins>;
|
||||
pinctrl-names = "default";
|
||||
button-0 {
|
||||
label = "JoySel";
|
||||
linux,code = <KEY_ENTER>;
|
||||
interrupt-parent = <&stmfx_pinctrl>;
|
||||
interrupts = <0 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
button-1 {
|
||||
label = "JoyDown";
|
||||
linux,code = <KEY_DOWN>;
|
||||
interrupt-parent = <&stmfx_pinctrl>;
|
||||
interrupts = <1 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
button-2 {
|
||||
label = "JoyLeft";
|
||||
linux,code = <KEY_LEFT>;
|
||||
interrupt-parent = <&stmfx_pinctrl>;
|
||||
interrupts = <2 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
button-3 {
|
||||
label = "JoyRight";
|
||||
linux,code = <KEY_RIGHT>;
|
||||
interrupt-parent = <&stmfx_pinctrl>;
|
||||
interrupts = <3 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
button-4 {
|
||||
label = "JoyUp";
|
||||
linux,code = <KEY_UP>;
|
||||
interrupt-parent = <&stmfx_pinctrl>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_RISING>;
|
||||
};
|
||||
};
|
||||
|
||||
panel_backlight: panel-backlight {
|
||||
compatible = "gpio-backlight";
|
||||
gpios = <&gpiod 13 GPIO_ACTIVE_LOW>;
|
||||
default-on;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&cec {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&cec_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&dcmi {
|
||||
status = "okay";
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&dcmi_pins_a>;
|
||||
pinctrl-1 = <&dcmi_sleep_pins_a>;
|
||||
|
||||
port {
|
||||
dcmi_0: endpoint {
|
||||
remote-endpoint = <&ov5640_0>;
|
||||
bus-width = <8>;
|
||||
hsync-active = <0>;
|
||||
vsync-active = <0>;
|
||||
pclk-sample = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dsi {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
phy-dsi-supply = <®18>;
|
||||
status = "okay";
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
dsi_in: endpoint {
|
||||
remote-endpoint = <<dc_ep0_out>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
dsi_out: endpoint {
|
||||
remote-endpoint = <&dsi_panel_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
panel-dsi@0 {
|
||||
compatible = "raydium,rm68200";
|
||||
reg = <0>;
|
||||
reset-gpios = <&gpiof 15 GPIO_ACTIVE_LOW>;
|
||||
backlight = <&panel_backlight>;
|
||||
power-supply = <&v3v3>;
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
dsi_panel_in: endpoint {
|
||||
remote-endpoint = <&dsi_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ðernet0 {
|
||||
status = "okay";
|
||||
pinctrl-0 = <ðernet0_rgmii_pins_a>;
|
||||
pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
|
||||
pinctrl-names = "default", "sleep";
|
||||
phy-mode = "rgmii-id";
|
||||
max-speed = <1000>;
|
||||
phy-handle = <&phy0>;
|
||||
|
||||
mdio0 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
compatible = "snps,dwmac-mdio";
|
||||
phy0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&fmc {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&fmc_pins_a>;
|
||||
pinctrl-1 = <&fmc_sleep_pins_a>;
|
||||
status = "okay";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
nand@0 {
|
||||
reg = <0>;
|
||||
nand-on-flash-bbt;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c2_pins_a>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
|
||||
ov5640: camera@3c {
|
||||
compatible = "ovti,ov5640";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&ov5640_pins>;
|
||||
reg = <0x3c>;
|
||||
clocks = <&clk_ext_camera>;
|
||||
clock-names = "xclk";
|
||||
DOVDD-supply = <&v2v8>;
|
||||
powerdown-gpios = <&stmfx_pinctrl 18 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpios = <&stmfx_pinctrl 19 GPIO_ACTIVE_LOW>;
|
||||
rotation = <180>;
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
ov5640_0: endpoint {
|
||||
remote-endpoint = <&dcmi_0>;
|
||||
bus-width = <8>;
|
||||
data-shift = <2>; /* lines 9:2 are used */
|
||||
hsync-active = <0>;
|
||||
vsync-active = <0>;
|
||||
pclk-sample = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
stmfx: stmfx@42 {
|
||||
compatible = "st,stmfx-0300";
|
||||
reg = <0x42>;
|
||||
interrupts = <8 IRQ_TYPE_EDGE_RISING>;
|
||||
interrupt-parent = <&gpioi>;
|
||||
vdd-supply = <&v3v3>;
|
||||
|
||||
stmfx_pinctrl: stmfx-pin-controller {
|
||||
compatible = "st,stmfx-0300-pinctrl";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <2>;
|
||||
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
|
||||
|
||||
joystick_pins: joystick {
|
||||
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
|
||||
drive-push-pull;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
ov5640_pins: camera {
|
||||
pins = "agpio2", "agpio3"; /* stmfx pins 18 & 19 */
|
||||
drive-push-pull;
|
||||
output-low;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&i2c5 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&i2c5_pins_a>;
|
||||
i2c-scl-rising-time-ns = <185>;
|
||||
i2c-scl-falling-time-ns = <20>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
<dc {
|
||||
status = "okay";
|
||||
|
||||
port {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ltdc_ep0_out: endpoint@0 {
|
||||
reg = <0>;
|
||||
remote-endpoint = <&dsi_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&m_can1 {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&m_can1_pins_a>;
|
||||
pinctrl-1 = <&m_can1_sleep_pins_a>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qspi {
|
||||
pinctrl-names = "default", "sleep";
|
||||
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
|
||||
pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
|
||||
reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
status = "okay";
|
||||
|
||||
flash0: mx66l51235l@0 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <0>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-max-frequency = <108000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
|
||||
flash1: mx66l51235l@1 {
|
||||
compatible = "jedec,spi-nor";
|
||||
reg = <1>;
|
||||
spi-rx-bus-width = <4>;
|
||||
spi-max-frequency = <108000000>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
};
|
||||
};
|
||||
|
||||
&spi1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi1_pins_a>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&timers2 {
|
||||
/* spare dmas for other usage (un-delete to enable pwm capture) */
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
status = "disabled";
|
||||
pwm {
|
||||
pinctrl-0 = <&pwm2_pins_a>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
timer@1 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&timers8 {
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
status = "disabled";
|
||||
pwm {
|
||||
pinctrl-0 = <&pwm8_pins_a>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
timer@7 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&timers12 {
|
||||
/delete-property/dmas;
|
||||
/delete-property/dma-names;
|
||||
status = "disabled";
|
||||
pwm {
|
||||
pinctrl-0 = <&pwm12_pins_a>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
};
|
||||
timer@11 {
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&usbh_ehci {
|
||||
phys = <&usbphyc_port0>;
|
||||
phy-names = "usb";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg_hs {
|
||||
dr_mode = "peripheral";
|
||||
phys = <&usbphyc_port1 0>;
|
||||
phy-names = "usb2-phy";
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphyc {
|
||||
status = "okay";
|
||||
};
|
||||
Reference in New Issue
Block a user