GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)
This commit is contained in:
@@ -0,0 +1,236 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* common reset-controller functions for B&R boards
|
||||
*
|
||||
* Copyright (C) 2019 Hannes Schmelzer <oe5hpm@oevsv.at>
|
||||
* B&R Industrial Automation GmbH - http://www.br-automation.com/ *
|
||||
*/
|
||||
#include <common.h>
|
||||
#include <env.h>
|
||||
#include <errno.h>
|
||||
#include <i2c.h>
|
||||
#include <dm/uclass.h>
|
||||
#include "br_resetc.h"
|
||||
|
||||
/* I2C Address of controller */
|
||||
#define RSTCTRL_ADDR_PSOC 0x75
|
||||
#define RSTCTRL_ADDR_STM32 0x60
|
||||
|
||||
#define BMODE_DEFAULTAR 0
|
||||
#define BMODE_SERVICE 2
|
||||
#define BMODE_RUN 4
|
||||
#define BMODE_PME 12
|
||||
#define BMODE_DIAG 15
|
||||
|
||||
#ifdef CONFIG_LCD
|
||||
#include <lcd.h>
|
||||
#define LCD_SETCURSOR(x, y) lcd_position_cursor(x, y)
|
||||
#define LCD_PUTS(x) lcd_puts(x)
|
||||
#else
|
||||
#define LCD_SETCURSOR(x, y)
|
||||
#define LCD_PUTS(x)
|
||||
#endif /* CONFIG_LCD */
|
||||
|
||||
static const char *bootmodeascii[16] = {
|
||||
"BOOT", "reserved", "reserved", "reserved",
|
||||
"RUN", "reserved", "reserved", "reserved",
|
||||
"reserved", "reserved", "reserved", "reserved",
|
||||
"PME", "reserved", "reserved", "DIAG",
|
||||
};
|
||||
|
||||
struct br_reset_t {
|
||||
struct udevice *i2cdev;
|
||||
u8 is_psoc;
|
||||
};
|
||||
|
||||
static struct br_reset_t resetc;
|
||||
|
||||
__weak int board_boot_key(void)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
|
||||
__weak void board_boot_led(unsigned int on)
|
||||
{
|
||||
}
|
||||
|
||||
static int resetc_init(void)
|
||||
{
|
||||
struct udevice *i2cbus;
|
||||
int rc;
|
||||
|
||||
rc = uclass_get_device_by_seq(UCLASS_I2C, 0, &i2cbus);
|
||||
if (rc) {
|
||||
printf("Cannot find I2C bus #0!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
resetc.is_psoc = 1;
|
||||
rc = dm_i2c_probe(i2cbus,
|
||||
RSTCTRL_ADDR_PSOC, 0, &resetc.i2cdev);
|
||||
if (rc) {
|
||||
resetc.is_psoc = 0;
|
||||
rc = dm_i2c_probe(i2cbus,
|
||||
RSTCTRL_ADDR_STM32, 0, &resetc.i2cdev);
|
||||
}
|
||||
|
||||
if (rc)
|
||||
printf("Warning: cannot probe BuR resetcontroller!\n");
|
||||
|
||||
return rc;
|
||||
}
|
||||
|
||||
int br_resetc_regget(u8 reg, u8 *dst)
|
||||
{
|
||||
int rc = 0;
|
||||
|
||||
if (!resetc.i2cdev)
|
||||
rc = resetc_init();
|
||||
|
||||
if (rc != 0)
|
||||
return rc;
|
||||
|
||||
return dm_i2c_read(resetc.i2cdev, reg, dst, 1);
|
||||
}
|
||||
|
||||
int br_resetc_regset(u8 reg, u8 val)
|
||||
{
|
||||
int rc = 0;
|
||||
u16 regw = (val << 8) | val;
|
||||
|
||||
if (!resetc.i2cdev)
|
||||
rc = resetc_init();
|
||||
|
||||
if (rc != 0)
|
||||
return rc;
|
||||
|
||||
if (resetc.is_psoc)
|
||||
return dm_i2c_write(resetc.i2cdev, reg, (u8 *)®w, 2);
|
||||
|
||||
return dm_i2c_write(resetc.i2cdev, reg, (u8 *)®w, 1);
|
||||
}
|
||||
|
||||
int br_resetc_bmode(void)
|
||||
{
|
||||
int rc = 0;
|
||||
u16 regw;
|
||||
u8 regb, scr;
|
||||
int cnt;
|
||||
unsigned int bmode = 0;
|
||||
|
||||
if (!resetc.i2cdev)
|
||||
rc = resetc_init();
|
||||
|
||||
if (rc != 0)
|
||||
return rc;
|
||||
|
||||
rc = dm_i2c_read(resetc.i2cdev, RSTCTRL_ENHSTATUS, ®b, 1);
|
||||
if (rc != 0) {
|
||||
printf("WARN: cannot read ENHSTATUS from resetcontroller!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
rc = dm_i2c_read(resetc.i2cdev, RSTCTRL_SCRATCHREG0, &scr, 1);
|
||||
if (rc != 0) {
|
||||
printf("WARN: cannot read SCRATCHREG from resetcontroller!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
board_boot_led(1);
|
||||
|
||||
/* special bootmode from resetcontroller */
|
||||
if (regb & 0x4) {
|
||||
bmode = BMODE_DIAG;
|
||||
} else if (regb & 0x8) {
|
||||
bmode = BMODE_DEFAULTAR;
|
||||
} else if (board_boot_key() != 0) {
|
||||
cnt = 4;
|
||||
do {
|
||||
LCD_SETCURSOR(1, 8);
|
||||
switch (cnt) {
|
||||
case 4:
|
||||
LCD_PUTS
|
||||
("release KEY to enter SERVICE-mode. ");
|
||||
break;
|
||||
case 3:
|
||||
LCD_PUTS
|
||||
("release KEY to enter DIAGNOSE-mode. ");
|
||||
break;
|
||||
case 2:
|
||||
LCD_PUTS
|
||||
("release KEY to enter BOOT-mode. ");
|
||||
break;
|
||||
}
|
||||
mdelay(1000);
|
||||
cnt--;
|
||||
if (board_boot_key() == 0)
|
||||
break;
|
||||
} while (cnt);
|
||||
|
||||
switch (cnt) {
|
||||
case 0:
|
||||
bmode = BMODE_PME;
|
||||
break;
|
||||
case 1:
|
||||
bmode = BMODE_DEFAULTAR;
|
||||
break;
|
||||
case 2:
|
||||
bmode = BMODE_DIAG;
|
||||
break;
|
||||
case 3:
|
||||
bmode = BMODE_SERVICE;
|
||||
break;
|
||||
}
|
||||
} else if ((regb & 0x1) || scr == 0xCC) {
|
||||
bmode = BMODE_PME;
|
||||
} else {
|
||||
bmode = BMODE_RUN;
|
||||
}
|
||||
|
||||
LCD_SETCURSOR(1, 8);
|
||||
|
||||
switch (bmode) {
|
||||
case BMODE_PME:
|
||||
LCD_PUTS("entering PME-Mode (netscript). ");
|
||||
regw = 0x0C0C;
|
||||
break;
|
||||
case BMODE_DEFAULTAR:
|
||||
LCD_PUTS("entering BOOT-mode. ");
|
||||
regw = 0x0000;
|
||||
break;
|
||||
case BMODE_DIAG:
|
||||
LCD_PUTS("entering DIAGNOSE-mode. ");
|
||||
regw = 0x0F0F;
|
||||
break;
|
||||
case BMODE_SERVICE:
|
||||
LCD_PUTS("entering SERVICE mode. ");
|
||||
regw = 0xB4B4;
|
||||
break;
|
||||
case BMODE_RUN:
|
||||
LCD_PUTS("loading OS... ");
|
||||
regw = 0x0404;
|
||||
break;
|
||||
}
|
||||
|
||||
board_boot_led(0);
|
||||
|
||||
if (resetc.is_psoc)
|
||||
rc = dm_i2c_write(resetc.i2cdev, RSTCTRL_SCRATCHREG0,
|
||||
(u8 *)®w, 2);
|
||||
else
|
||||
rc = dm_i2c_write(resetc.i2cdev, RSTCTRL_SCRATCHREG0,
|
||||
(u8 *)®w, 1);
|
||||
|
||||
if (rc != 0)
|
||||
printf("WARN: cannot write into resetcontroller!\n");
|
||||
|
||||
if (resetc.is_psoc)
|
||||
printf("Reset: PSOC controller\n");
|
||||
else
|
||||
printf("Reset: STM32 controller\n");
|
||||
|
||||
printf("Mode: %s\n", bootmodeascii[regw & 0x0F]);
|
||||
env_set_ulong("b_mode", regw & 0x0F);
|
||||
|
||||
return rc;
|
||||
}
|
||||
@@ -0,0 +1,26 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* common reset-controller functions for B&R boards
|
||||
*
|
||||
* Copyright (C) 2019 Hannes Schmelzer <oe5hpm@oevsv.at>
|
||||
* B&R Industrial Automation GmbH - http://www.br-automation.com/ *
|
||||
*/
|
||||
#ifndef __CONFIG_BRRESETC_H__
|
||||
#define __CONFIG_BRRESETC_H__
|
||||
#include <common.h>
|
||||
|
||||
int br_resetc_regget(u8 reg, u8 *dst);
|
||||
int br_resetc_regset(u8 reg, u8 val);
|
||||
int br_resetc_bmode(void);
|
||||
|
||||
/* reset controller register defines */
|
||||
#define RSTCTRL_CTRLREG 0x01
|
||||
#define RSTCTRL_SCRATCHREG0 0x04
|
||||
#define RSTCTRL_ENHSTATUS 0x07
|
||||
#define RSTCTRL_SCRATCHREG1 0x08
|
||||
#define RSTCTRL_RSTCAUSE 0x00
|
||||
#define RSTCTRL_ERSTCAUSE 0x09
|
||||
#define RSTCTRL_SPECGPIO_I 0x0A
|
||||
#define RSTCTRL_SPECGPIO_O 0x0B
|
||||
|
||||
#endif /* __CONFIG_BRRESETC_H__ */
|
||||
@@ -0,0 +1,26 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* bur_comon.h
|
||||
*
|
||||
* common board information header for B&R boards
|
||||
*
|
||||
* Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
|
||||
* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
|
||||
*/
|
||||
|
||||
#ifndef _BUR_COMMON_H_
|
||||
#define _BUR_COMMON_H_
|
||||
|
||||
#include <../../../drivers/video/am335x-fb.h>
|
||||
|
||||
int load_lcdtiming(struct am335x_lcdpanel *panel);
|
||||
void br_summaryscreen(void);
|
||||
void pmicsetup(u32 mpupll, unsigned int bus);
|
||||
void enable_uart0_pin_mux(void);
|
||||
void enable_i2c_pin_mux(void);
|
||||
void enable_board_pin_mux(void);
|
||||
int board_eth_init(bd_t *bis);
|
||||
|
||||
int brdefaultip_setup(int bus, int chip);
|
||||
|
||||
#endif
|
||||
@@ -0,0 +1,401 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* common.c
|
||||
*
|
||||
* common board functions for B&R boards
|
||||
*
|
||||
* Copyright (C) 2013 Hannes Schmelzer <oe5hpm@oevsv.at>
|
||||
* Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com
|
||||
*
|
||||
*/
|
||||
#include <version.h>
|
||||
#include <common.h>
|
||||
#include <env.h>
|
||||
#include <fdtdec.h>
|
||||
#include <i2c.h>
|
||||
#include <lcd.h>
|
||||
#include "bur_common.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
/* --------------------------------------------------------------------------*/
|
||||
#if defined(CONFIG_LCD) && defined(CONFIG_AM335X_LCD) && \
|
||||
!defined(CONFIG_SPL_BUILD)
|
||||
#include <asm/arch/hardware.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/gpio.h>
|
||||
#include <power/tps65217.h>
|
||||
#include "../../../drivers/video/am335x-fb.h"
|
||||
|
||||
void lcdbacklight(int on)
|
||||
{
|
||||
unsigned int driver = env_get_ulong("ds1_bright_drv", 16, 0UL);
|
||||
unsigned int bright = env_get_ulong("ds1_bright_def", 10, 50);
|
||||
unsigned int pwmfrq = env_get_ulong("ds1_pwmfreq", 10, ~0UL);
|
||||
unsigned int tmp;
|
||||
struct gptimer *timerhw;
|
||||
|
||||
if (on)
|
||||
bright = bright != ~0UL ? bright : 50;
|
||||
else
|
||||
bright = 0;
|
||||
|
||||
switch (driver) {
|
||||
case 2:
|
||||
timerhw = (struct gptimer *)DM_TIMER5_BASE;
|
||||
break;
|
||||
default:
|
||||
timerhw = (struct gptimer *)DM_TIMER6_BASE;
|
||||
}
|
||||
|
||||
switch (driver) {
|
||||
case 0: /* PMIC LED-Driver */
|
||||
/* brightness level */
|
||||
tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
|
||||
TPS65217_WLEDCTRL2, bright, 0xFF);
|
||||
/* current sink */
|
||||
tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
|
||||
TPS65217_WLEDCTRL1,
|
||||
bright != 0 ? 0x0A : 0x02,
|
||||
0xFF);
|
||||
break;
|
||||
case 1:
|
||||
case 2: /* PWM using timer */
|
||||
if (pwmfrq != ~0UL) {
|
||||
timerhw->tiocp_cfg = TCFG_RESET;
|
||||
udelay(10);
|
||||
while (timerhw->tiocp_cfg & TCFG_RESET)
|
||||
;
|
||||
tmp = ~0UL-(V_OSCK/pwmfrq); /* bottom value */
|
||||
timerhw->tldr = tmp;
|
||||
timerhw->tcrr = tmp;
|
||||
tmp = tmp + ((V_OSCK/pwmfrq)/100) * bright;
|
||||
timerhw->tmar = tmp;
|
||||
timerhw->tclr = (TCLR_PT | (2 << TCLR_TRG_SHIFT) |
|
||||
TCLR_CE | TCLR_AR | TCLR_ST);
|
||||
} else {
|
||||
puts("invalid pwmfrq in env/dtb! skip PWM-setup.\n");
|
||||
}
|
||||
break;
|
||||
default:
|
||||
puts("no suitable backlightdriver in env/dtb!\n");
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
int load_lcdtiming(struct am335x_lcdpanel *panel)
|
||||
{
|
||||
struct am335x_lcdpanel pnltmp;
|
||||
|
||||
pnltmp.hactive = env_get_ulong("ds1_hactive", 10, ~0UL);
|
||||
pnltmp.vactive = env_get_ulong("ds1_vactive", 10, ~0UL);
|
||||
pnltmp.bpp = env_get_ulong("ds1_bpp", 10, ~0UL);
|
||||
pnltmp.hfp = env_get_ulong("ds1_hfp", 10, ~0UL);
|
||||
pnltmp.hbp = env_get_ulong("ds1_hbp", 10, ~0UL);
|
||||
pnltmp.hsw = env_get_ulong("ds1_hsw", 10, ~0UL);
|
||||
pnltmp.vfp = env_get_ulong("ds1_vfp", 10, ~0UL);
|
||||
pnltmp.vbp = env_get_ulong("ds1_vbp", 10, ~0UL);
|
||||
pnltmp.vsw = env_get_ulong("ds1_vsw", 10, ~0UL);
|
||||
pnltmp.pxl_clk = env_get_ulong("ds1_pxlclk", 10, ~0UL);
|
||||
pnltmp.pol = env_get_ulong("ds1_pol", 16, ~0UL);
|
||||
pnltmp.pup_delay = env_get_ulong("ds1_pupdelay", 10, ~0UL);
|
||||
pnltmp.pon_delay = env_get_ulong("ds1_tondelay", 10, ~0UL);
|
||||
panel_info.vl_rot = env_get_ulong("ds1_rotation", 10, 0);
|
||||
|
||||
if (
|
||||
~0UL == (pnltmp.hactive) ||
|
||||
~0UL == (pnltmp.vactive) ||
|
||||
~0UL == (pnltmp.bpp) ||
|
||||
~0UL == (pnltmp.hfp) ||
|
||||
~0UL == (pnltmp.hbp) ||
|
||||
~0UL == (pnltmp.hsw) ||
|
||||
~0UL == (pnltmp.vfp) ||
|
||||
~0UL == (pnltmp.vbp) ||
|
||||
~0UL == (pnltmp.vsw) ||
|
||||
~0UL == (pnltmp.pxl_clk) ||
|
||||
~0UL == (pnltmp.pol) ||
|
||||
~0UL == (pnltmp.pup_delay) ||
|
||||
~0UL == (pnltmp.pon_delay)
|
||||
) {
|
||||
puts("lcd-settings in env/dtb incomplete!\n");
|
||||
printf("display-timings:\n"
|
||||
"================\n"
|
||||
"hactive: %d\n"
|
||||
"vactive: %d\n"
|
||||
"bpp : %d\n"
|
||||
"hfp : %d\n"
|
||||
"hbp : %d\n"
|
||||
"hsw : %d\n"
|
||||
"vfp : %d\n"
|
||||
"vbp : %d\n"
|
||||
"vsw : %d\n"
|
||||
"pxlclk : %d\n"
|
||||
"pol : 0x%08x\n"
|
||||
"pondly : %d\n",
|
||||
pnltmp.hactive, pnltmp.vactive, pnltmp.bpp,
|
||||
pnltmp.hfp, pnltmp.hbp, pnltmp.hsw,
|
||||
pnltmp.vfp, pnltmp.vbp, pnltmp.vsw,
|
||||
pnltmp.pxl_clk, pnltmp.pol, pnltmp.pon_delay);
|
||||
|
||||
return -1;
|
||||
}
|
||||
debug("lcd-settings in env complete, taking over.\n");
|
||||
memcpy((void *)panel,
|
||||
(void *)&pnltmp,
|
||||
sizeof(struct am335x_lcdpanel));
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void br_summaryscreen_printenv(char *prefix,
|
||||
char *name, char *altname,
|
||||
char *suffix)
|
||||
{
|
||||
char *envval = env_get(name);
|
||||
if (0 != envval) {
|
||||
lcd_printf("%s %s %s", prefix, envval, suffix);
|
||||
} else if (0 != altname) {
|
||||
envval = env_get(altname);
|
||||
if (0 != envval)
|
||||
lcd_printf("%s %s %s", prefix, envval, suffix);
|
||||
} else {
|
||||
lcd_printf("\n");
|
||||
}
|
||||
}
|
||||
|
||||
void br_summaryscreen(void)
|
||||
{
|
||||
br_summaryscreen_printenv(" - B&R -", "br_orderno", 0, "-\n");
|
||||
br_summaryscreen_printenv(" Serial/Rev :", "br_serial", 0, "\n");
|
||||
br_summaryscreen_printenv(" MAC1 :", "br_mac1", "ethaddr", "\n");
|
||||
br_summaryscreen_printenv(" MAC2 :", "br_mac2", 0, "\n");
|
||||
lcd_puts(" Bootloader : " PLAIN_VERSION "\n");
|
||||
lcd_puts("\n");
|
||||
}
|
||||
|
||||
void lcdpower(int on)
|
||||
{
|
||||
u32 pin, swval, i;
|
||||
char buf[16] = { 0 };
|
||||
|
||||
pin = env_get_ulong("ds1_pwr", 16, ~0UL);
|
||||
|
||||
if (pin == ~0UL) {
|
||||
puts("no pwrpin in dtb/env, cannot powerup display!\n");
|
||||
return;
|
||||
}
|
||||
|
||||
for (i = 0; i < 3; i++) {
|
||||
if (pin != 0) {
|
||||
snprintf(buf, sizeof(buf), "ds1_pwr#%d", i);
|
||||
if (gpio_request(pin & 0x7F, buf) != 0) {
|
||||
printf("%s: not able to request gpio %s",
|
||||
__func__, buf);
|
||||
continue;
|
||||
}
|
||||
swval = pin & 0x80 ? 0 : 1;
|
||||
if (on)
|
||||
gpio_direction_output(pin & 0x7F, swval);
|
||||
else
|
||||
gpio_direction_output(pin & 0x7F, !swval);
|
||||
|
||||
debug("switched pin %d to %d\n", pin & 0x7F, swval);
|
||||
}
|
||||
pin >>= 8;
|
||||
}
|
||||
}
|
||||
|
||||
vidinfo_t panel_info = {
|
||||
.vl_col = 1366, /*
|
||||
* give full resolution for allocating enough
|
||||
* memory
|
||||
*/
|
||||
.vl_row = 768,
|
||||
.vl_bpix = 5,
|
||||
.priv = 0
|
||||
};
|
||||
|
||||
void lcd_ctrl_init(void *lcdbase)
|
||||
{
|
||||
struct am335x_lcdpanel lcd_panel;
|
||||
|
||||
memset(&lcd_panel, 0, sizeof(struct am335x_lcdpanel));
|
||||
if (load_lcdtiming(&lcd_panel) != 0)
|
||||
return;
|
||||
|
||||
lcd_panel.panel_power_ctrl = &lcdpower;
|
||||
|
||||
if (0 != am335xfb_init(&lcd_panel))
|
||||
printf("ERROR: failed to initialize video!");
|
||||
/*
|
||||
* modifiy panel info to 'real' resolution, to operate correct with
|
||||
* lcd-framework.
|
||||
*/
|
||||
panel_info.vl_col = lcd_panel.hactive;
|
||||
panel_info.vl_row = lcd_panel.vactive;
|
||||
|
||||
lcd_set_flush_dcache(1);
|
||||
}
|
||||
|
||||
void lcd_enable(void)
|
||||
{
|
||||
br_summaryscreen();
|
||||
lcdbacklight(1);
|
||||
}
|
||||
#endif /* CONFIG_LCD */
|
||||
|
||||
int ft_board_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
int nodeoffset;
|
||||
|
||||
nodeoffset = fdt_path_offset(blob, "/factory-settings");
|
||||
if (nodeoffset < 0) {
|
||||
printf("%s: cannot find /factory-settings, trying /fset\n",
|
||||
__func__);
|
||||
nodeoffset = fdt_path_offset(blob, "/fset");
|
||||
if (nodeoffset < 0) {
|
||||
printf("%s: cannot find /fset.\n", __func__);
|
||||
return 0;
|
||||
}
|
||||
}
|
||||
|
||||
if (fdt_setprop(blob, nodeoffset, "bl-version",
|
||||
PLAIN_VERSION, strlen(PLAIN_VERSION)) != 0) {
|
||||
printf("%s: no 'bl-version' prop in fdt!\n", __func__);
|
||||
return 0;
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
int brdefaultip_setup(int bus, int chip)
|
||||
{
|
||||
int rc;
|
||||
struct udevice *i2cdev;
|
||||
u8 u8buf = 0;
|
||||
char defip[256] = { 0 };
|
||||
|
||||
rc = i2c_get_chip_for_busnum(bus, chip, 2, &i2cdev);
|
||||
if (rc != 0) {
|
||||
printf("WARN: cannot probe baseboard EEPROM!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
rc = dm_i2c_read(i2cdev, 0, &u8buf, 1);
|
||||
if (rc != 0) {
|
||||
printf("WARN: cannot read baseboard EEPROM!\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
if (u8buf != 0xFF)
|
||||
snprintf(defip, sizeof(defip),
|
||||
"if test -r ${ipaddr}; then; else setenv ipaddr 192.168.60.%d; setenv serverip 192.168.60.254; setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;",
|
||||
u8buf);
|
||||
else
|
||||
strncpy(defip,
|
||||
"if test -r ${ipaddr}; then; else setenv ipaddr 192.168.60.1; setenv serverip 192.168.60.254; setenv gatewayip 192.168.60.254; setenv netmask 255.255.255.0; fi;",
|
||||
sizeof(defip));
|
||||
|
||||
env_set("brdefaultip", defip);
|
||||
env_set_hex("board_id", u8buf);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int overwrite_console(void)
|
||||
{
|
||||
return 1;
|
||||
}
|
||||
|
||||
#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_AM33XX)
|
||||
#include <asm/arch/hardware.h>
|
||||
#include <asm/arch/omap.h>
|
||||
#include <asm/arch/clock.h>
|
||||
#include <asm/arch/sys_proto.h>
|
||||
#include <power/tps65217.h>
|
||||
|
||||
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
|
||||
|
||||
void pmicsetup(u32 mpupll, unsigned int bus)
|
||||
{
|
||||
int mpu_vdd;
|
||||
int usb_cur_lim;
|
||||
|
||||
if (power_tps65217_init(bus)) {
|
||||
printf("WARN: cannot setup PMIC 0x24 @ bus #%d, not found!.\n",
|
||||
bus);
|
||||
return;
|
||||
}
|
||||
|
||||
/* Get the frequency which is defined by device fuses */
|
||||
dpll_mpu_opp100.m = am335x_get_efuse_mpu_max_freq(cdev);
|
||||
printf("detected max. frequency: %d - ", dpll_mpu_opp100.m);
|
||||
|
||||
if (0 != mpupll) {
|
||||
dpll_mpu_opp100.m = mpupll;
|
||||
printf("retuning MPU-PLL to: %d MHz.\n", dpll_mpu_opp100.m);
|
||||
} else {
|
||||
puts("ok.\n");
|
||||
}
|
||||
/*
|
||||
* Increase USB current limit to 1300mA or 1800mA and set
|
||||
* the MPU voltage controller as needed.
|
||||
*/
|
||||
if (dpll_mpu_opp100.m == MPUPLL_M_1000) {
|
||||
usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1800MA;
|
||||
mpu_vdd = TPS65217_DCDC_VOLT_SEL_1325MV;
|
||||
} else {
|
||||
usb_cur_lim = TPS65217_USB_INPUT_CUR_LIMIT_1300MA;
|
||||
mpu_vdd = TPS65217_DCDC_VOLT_SEL_1275MV;
|
||||
}
|
||||
|
||||
if (tps65217_reg_write(TPS65217_PROT_LEVEL_NONE, TPS65217_POWER_PATH,
|
||||
usb_cur_lim, TPS65217_USB_INPUT_CUR_LIMIT_MASK))
|
||||
puts("tps65217_reg_write failure\n");
|
||||
|
||||
/* Set DCDC3 (CORE) voltage to 1.125V */
|
||||
if (tps65217_voltage_update(TPS65217_DEFDCDC3,
|
||||
TPS65217_DCDC_VOLT_SEL_1125MV)) {
|
||||
puts("tps65217_voltage_update failure\n");
|
||||
return;
|
||||
}
|
||||
|
||||
/* Set CORE Frequencies to OPP100 */
|
||||
do_setup_dpll(&dpll_core_regs, &dpll_core_opp100);
|
||||
|
||||
/* Set DCDC2 (MPU) voltage */
|
||||
if (tps65217_voltage_update(TPS65217_DEFDCDC2, mpu_vdd)) {
|
||||
puts("tps65217_voltage_update failure\n");
|
||||
return;
|
||||
}
|
||||
|
||||
/* Set LDO3 to 1.8V */
|
||||
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
|
||||
TPS65217_DEFLS1,
|
||||
TPS65217_LDO_VOLTAGE_OUT_1_8,
|
||||
TPS65217_LDO_MASK))
|
||||
puts("tps65217_reg_write failure\n");
|
||||
/* Set LDO4 to 3.3V */
|
||||
if (tps65217_reg_write(TPS65217_PROT_LEVEL_2,
|
||||
TPS65217_DEFLS2,
|
||||
TPS65217_LDO_VOLTAGE_OUT_3_3,
|
||||
TPS65217_LDO_MASK))
|
||||
puts("tps65217_reg_write failure\n");
|
||||
|
||||
/* Set MPU Frequency to what we detected now that voltages are set */
|
||||
do_setup_dpll(&dpll_mpu_regs, &dpll_mpu_opp100);
|
||||
/* Set PWR_EN bit in Status Register */
|
||||
tps65217_reg_write(TPS65217_PROT_LEVEL_NONE,
|
||||
TPS65217_STATUS, TPS65217_PWR_OFF, TPS65217_PWR_OFF);
|
||||
}
|
||||
|
||||
void set_uart_mux_conf(void)
|
||||
{
|
||||
enable_uart0_pin_mux();
|
||||
}
|
||||
|
||||
void set_mux_conf_regs(void)
|
||||
{
|
||||
enable_board_pin_mux();
|
||||
}
|
||||
|
||||
#endif /* CONFIG_SPL_BUILD && CONFIG_AM33XX */
|
||||
Reference in New Issue
Block a user