GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)

source/bootloader/u-boot-2020.01/board/amlogic/p212/README.libretech-cc

@@ -0,0 +1,135 @@
+U-Boot for LibreTech CC
+=======================
+
+LibreTech CC is a single board computer manufactured by Libre Technology
+with the following specifications:
+
+ - Amlogic S905X ARM Cortex-A53 quad-core SoC @ 1.5GHz
+ - ARM Mali 450 GPU
+ - 2GB DDR3 SDRAM
+ - 10/100 Ethernet
+ - HDMI 2.0 4K/60Hz display
+ - 40-pin GPIO header
+ - 4 x USB 2.0 Host
+ - eMMC, microSD
+ - Infrared receiver
+
+Schematics are available on the manufacturer website.
+
+Currently the U-Boot port supports the following devices:
+ - serial
+ - eMMC, microSD
+ - Ethernet
+ - I2C
+ - Regulators
+ - Reset controller
+ - Clock controller
+ - USB Host
+ - ADC
+
+U-Boot compilation
+==================
+
+ > export ARCH=arm
+ > export CROSS_COMPILE=aarch64-none-elf-
+ > make libretech-cc_defconfig
+ > make
+
+Image creation
+==============
+
+To boot the system, u-boot must be combined with several earlier stage
+bootloaders:
+
+* bl2.bin: vendor-provided binary blob
+* bl21.bin: built from vendor u-boot source
+* bl30.bin: vendor-provided binary blob
+* bl301.bin: built from vendor u-boot source
+* bl31.bin: vendor-provided binary blob
+* acs.bin: built from vendor u-boot source
+
+These binaries and the tools required below have been collected and prebuilt
+for convenience at <https://github.com/BayLibre/u-boot/releases/>
+
+Download and extract the libretech-cc release from there, and set FIPDIR to
+point to the `fip` subdirectory.
+
+ > export FIPDIR=/path/to/extracted/fip
+
+Alternatively, you can obtain the original vendor u-boot tree which
+contains the required blobs and sources, and build yourself.
+Note that old compilers are required for this to build. The compilers here
+are suggested by Amlogic, and they are 32-bit x86 binaries.
+
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > wget https://releases.linaro.org/archive/13.11/components/toolchain/binaries/gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-aarch64-none-elf-4.8-2013.11_linux.tar.xz
+ > tar xvfJ gcc-linaro-arm-none-eabi-4.8-2013.11_linux.tar.xz
+ > export PATH=$PWD/gcc-linaro-aarch64-none-elf-4.8-2013.11_linux/bin:$PWD/gcc-linaro-arm-none-eabi-4.8-2013.11_linux/bin:$PATH
+ > git clone https://github.com/BayLibre/u-boot.git -b libretech-cc amlogic-u-boot
+ > cd amlogic-u-boot
+ > make libretech_cc_defconfig
+ > make
+ > export FIPDIR=$PWD/fip
+
+Once you have the binaries available (either through the prebuilt download,
+or having built the vendor u-boot yourself), you can then proceed to glue
+everything together. Go back to mainline U-Boot source tree then :
+
+ > mkdir fip
+
+ > cp $FIPDIR/gxl/bl2.bin fip/
+ > cp $FIPDIR/gxl/acs.bin fip/
+ > cp $FIPDIR/gxl/bl21.bin fip/
+ > cp $FIPDIR/gxl/bl30.bin fip/
+ > cp $FIPDIR/gxl/bl301.bin fip/
+ > cp $FIPDIR/gxl/bl31.img fip/
+ > cp u-boot.bin fip/bl33.bin
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl30.bin \
+	fip/zero_tmp \
+	fip/bl30_zero.bin \
+	fip/bl301.bin \
+	fip/bl301_zero.bin \
+	fip/bl30_new.bin \
+	bl30
+
+ > $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+ > $FIPDIR/blx_fix.sh \
+	fip/bl2_acs.bin \
+	fip/zero_tmp \
+	fip/bl2_zero.bin \
+	fip/bl21.bin \
+	fip/bl21_zero.bin \
+	fip/bl2_new.bin \
+	bl2
+
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl3enc --input fip/bl33.bin
+ > $FIPDIR/gxl/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+ > $FIPDIR/gxl/aml_encrypt_gxl --bootmk \
+		--output fip/u-boot.bin \
+		--bl2 fip/bl2.n.bin.sig \
+		--bl30 fip/bl30_new.bin.enc \
+		--bl31 fip/bl31.img.enc \
+		--bl33 fip/bl33.bin.enc
+
+and then write the image to SD with:
+
+ > DEV=/dev/your_sd_device
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+ > dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
+
+Note that Amlogic provides aml_encrypt_gxl as a 32-bit x86 binary with no
+source code. Should you prefer to avoid that, there are open source reverse
+engineered versions available:
+
+1. gxlimg <https://github.com/repk/gxlimg>, which comes with a handy
+   Makefile that automates the whole process.
+2. meson-tools <https://github.com/afaerber/meson-tools>
+
+However, these community-developed alternatives are not endorsed by or
+supported by Amlogic.