GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)

source/bootloader/u-boot-2020.01/board/freescale/mx6ul_14x14_evk/Kconfig

@@ -0,0 +1,12 @@
+if TARGET_MX6UL_14X14_EVK || TARGET_MX6UL_9X9_EVK
+
+config SYS_BOARD
+	default "mx6ul_14x14_evk"
+
+config SYS_VENDOR
+	default "freescale"
+
+config SYS_CONFIG_NAME
+	default "mx6ul_14x14_evk"
+
+endif

source/bootloader/u-boot-2020.01/board/freescale/mx6ul_14x14_evk/MAINTAINERS

@@ -0,0 +1,7 @@
+MX6ULEVK BOARD
+M:	Peng Fan <peng.fan@nxp.com>
+S:	Maintained
+F:	board/freescale/mx6ul_14x14_evk/
+F:	include/configs/mx6ul_14x14_evk.h
+F:	configs/mx6ul_14x14_evk_defconfig
+F:	configs/mx6ul_9x9_evk_defconfig

source/bootloader/u-boot-2020.01/board/freescale/mx6ul_14x14_evk/Makefile

@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0+
+# (C) Copyright 2015 Freescale Semiconductor, Inc.
+
+obj-y  := mx6ul_14x14_evk.o

source/bootloader/u-boot-2020.01/board/freescale/mx6ul_14x14_evk/README

@@ -0,0 +1,82 @@
+How to use U-Boot on Freescale MX6UL 14x14 EVK
+-----------------------------------------------
+
+- Build U-Boot for MX6UL 14x14 EVK:
+
+$ make mrproper
+$ make mx6ul_14x14_evk_defconfig
+$ make
+
+This will generate the SPL image called SPL and the u-boot.img.
+
+1. Booting via SDCard
+---------------------
+
+- Flash the SPL image into the micro SD card:
+
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+
+- Flash the u-boot.img image into the micro SD card:
+
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Jumper settings:
+
+SW601: 0 0 1 0
+Sw602: 1 0
+
+where 0 means bottom position and 1 means top position (from the
+switch label numbers reference).
+
+- Connect the USB cable between the EVK and the PC for the console.
+(The USB console connector is the one close the push buttons)
+
+- Insert the micro SD card in the board, power it up and U-Boot messages should
+come up.
+
+2. Booting via Serial Download Protocol (SDP)
+---------------------------------------------
+
+The mx6ulevk board can boot from USB OTG port using the SDP, target will
+enter in SDP mode in case an SD Card is not connect or boot switches are
+set as below:
+
+Sw602: 0 1
+SW601: x x x x
+
+The following tools can be used to boot via SDP, for both tools you must
+connect an USB cable in USB OTG port.
+
+- Method 1: Universal Update Utility (uuu)
+
+The UUU binary can be downloaded in release tab from link below:
+https://github.com/NXPmicro/mfgtools
+
+The following script should be created to boot SPL + u-boot-dtb.img binaries:
+
+  $ cat uuu_script
+    uuu_version 1.1.4
+
+    SDP: boot -f SPL
+    SDPU: write -f u-boot-dtb.img -addr 0x877fffc0
+    SDPU: jump -addr 0x877fffc0
+    SDPU: done
+
+Please note that the address above is calculated based on SYS_TEXT_BASE address:
+
+0x877fffc0 = 0x87800000 (SYS_TEXT_BASE) - 0x40 (U-Boot proper Header size)
+
+Power on the target and run the following command from U-Boot root directory:
+
+  $ sudo ./uuu uuu_script
+
+- Method 2: imx usb loader tool (imx_usb):
+
+The imx_usb_loader tool can be downloaded in link below:
+https://github.com/boundarydevices/imx_usb_loader
+
+Build the source code and run the following commands from U-Boot root
+directory:
+
+  $ sudo ./imx_usb SPL
+  $ sudo ./imx_usb u-boot-dtb.img

source/bootloader/u-boot-2020.01/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c

@@ -0,0 +1,696 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ */
+
+#include <init.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6ul_pins.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/boot_mode.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <env.h>
+#include <fsl_esdhc_imx.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <linux/sizes.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../common/pfuze.h"
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_DAT3_CD_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |	\
+	PAD_CTL_PUS_100K_DOWN  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL    (PAD_CTL_PKE | PAD_CTL_PUE |            \
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
+	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |			\
+	PAD_CTL_ODE)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_SPEED_HIGH   |                                  \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST)
+
+#define LCD_PAD_CTRL    (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
+	PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm)
+
+#define MDIO_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
+	PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
+
+#define ENET_CLK_PAD_CTRL  (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+
+#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#ifdef CONFIG_DM_PMIC
+int power_init_board(void)
+{
+	struct udevice *dev;
+	int ret, dev_id, rev_id;
+	unsigned int reg;
+
+	ret = pmic_get("pfuze3000", &dev);
+	if (ret == -ENODEV)
+		return 0;
+	if (ret != 0)
+		return ret;
+
+	dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
+	rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
+	printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	reg = pmic_reg_read(dev, PFUZE3000_LDOGCTL);
+	reg |= 0x1;
+	pmic_reg_write(dev, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1B step ramp up time from 2us to 4us/25mV */
+	pmic_reg_write(dev, PFUZE3000_SW1BCONF, 0x40);
+
+	/* SW1B mode to APS/PFM */
+	pmic_reg_write(dev, PFUZE3000_SW1BMODE, 0xc);
+
+	/* SW1B standby voltage set to 0.975V */
+	pmic_reg_write(dev, PFUZE3000_SW1BSTBY, 0xb);
+
+	return 0;
+}
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/* VSELECT */
+	MX6_PAD_GPIO1_IO05__USDHC1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	/* CD */
+	MX6_PAD_UART1_RTS_B__GPIO1_IO19 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	/* RST_B */
+	MX6_PAD_GPIO1_IO09__GPIO1_IO09 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+/*
+ * mx6ul_14x14_evk board default supports sd card. If want to use
+ * EMMC, need to do board rework for sd2.
+ * Introduce CONFIG_MX6UL_14X14_EVK_EMMC_REWORK, if sd2 reworked to support
+ * emmc, need to define this macro.
+ */
+#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
+static iomux_v3_cfg_t const usdhc2_emmc_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+
+	/*
+	 * RST_B
+	 */
+	MX6_PAD_NAND_ALE__GPIO4_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+#else
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+/*
+ * The evk board uses DAT3 to detect CD card plugin,
+ * in u-boot we mux the pin to GPIO when doing board_mmc_getcd.
+ */
+static iomux_v3_cfg_t const usdhc2_cd_pad =
+	MX6_PAD_NAND_DATA03__GPIO4_IO05 | MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
+
+static iomux_v3_cfg_t const usdhc2_dat3_pad =
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 |
+	MUX_PAD_CTRL(USDHC_DAT3_CD_PAD_CTRL);
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_FSL_QSPI
+static int board_qspi_init(void)
+{
+	/* Set the clock */
+	enable_qspi_clk(0);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_FSL_ESDHC_IMX
+static struct fsl_esdhc_cfg usdhc_cfg[2] = {
+	{USDHC1_BASE_ADDR, 0, 4},
+#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
+	{USDHC2_BASE_ADDR, 0, 8},
+#else
+	{USDHC2_BASE_ADDR, 0, 4},
+#endif
+};
+
+#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 19)
+#define USDHC1_PWR_GPIO	IMX_GPIO_NR(1, 9)
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(4, 5)
+#define USDHC2_PWR_GPIO	IMX_GPIO_NR(4, 10)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC1_BASE_ADDR:
+		ret = !gpio_get_value(USDHC1_CD_GPIO);
+		break;
+	case USDHC2_BASE_ADDR:
+#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
+		ret = 1;
+#else
+		imx_iomux_v3_setup_pad(usdhc2_cd_pad);
+		gpio_request(USDHC2_CD_GPIO, "usdhc2 cd");
+		gpio_direction_input(USDHC2_CD_GPIO);
+
+		/*
+		 * Since it is the DAT3 pin, this pin is pulled to
+		 * low voltage if no card
+		 */
+		ret = gpio_get_value(USDHC2_CD_GPIO);
+
+		imx_iomux_v3_setup_pad(usdhc2_dat3_pad);
+#endif
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	/*
+	 * According to the board_mmc_init() the following map is done:
+	 * (U-Boot device node)    (Physical Port)
+	 * mmc0                    USDHC1
+	 * mmc1                    USDHC2
+	 */
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
+			gpio_request(USDHC1_CD_GPIO, "usdhc1 cd");
+			gpio_direction_input(USDHC1_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+
+			gpio_direction_output(USDHC1_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC1_PWR_GPIO, 1);
+			break;
+		case 1:
+#if defined(CONFIG_MX6UL_14X14_EVK_EMMC_REWORK)
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_emmc_pads, ARRAY_SIZE(usdhc2_emmc_pads));
+#else
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+#endif
+			gpio_request(USDHC2_PWR_GPIO, "usdhc2 pwr");
+			gpio_direction_output(USDHC2_PWR_GPIO, 0);
+			udelay(500);
+			gpio_direction_output(USDHC2_PWR_GPIO, 1);
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers (%d) than supported by the board\n", i + 1);
+			return -EINVAL;
+			}
+
+			ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+			if (ret) {
+				printf("Warning: failed to initialize mmc dev %d\n", i);
+				return ret;
+			}
+	}
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX6
+#ifndef CONFIG_DM_USB
+
+#define USB_OTHERREGS_OFFSET	0x800
+#define UCTRL_PWR_POL		(1 << 9)
+
+static iomux_v3_cfg_t const usb_otg_pads[] = {
+	MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
+};
+
+/* At default the 3v3 enables the MIC2026 for VBUS power */
+static void setup_usb(void)
+{
+	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
+					 ARRAY_SIZE(usb_otg_pads));
+}
+
+int board_usb_phy_mode(int port)
+{
+	if (port == 1)
+		return USB_INIT_HOST;
+	else
+		return usb_phy_mode(port);
+}
+
+int board_ehci_hcd_init(int port)
+{
+	u32 *usbnc_usb_ctrl;
+
+	if (port > 1)
+		return -EINVAL;
+
+	usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+				 port * 4);
+
+	/* Set Power polarity */
+	setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+	return 0;
+}
+#endif
+#endif
+
+#ifdef CONFIG_FEC_MXC
+/*
+ * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
+ * be used for ENET1 or ENET2, cannot be used for both.
+ */
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+
+	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(int fec_id)
+{
+	if (fec_id == 0)
+		imx_iomux_v3_setup_multiple_pads(fec1_pads,
+						 ARRAY_SIZE(fec1_pads));
+	else
+		imx_iomux_v3_setup_multiple_pads(fec2_pads,
+						 ARRAY_SIZE(fec2_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_fec(CONFIG_FEC_ENET_DEV);
+
+	return fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
+				       CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	if (fec_id == 0) {
+		/*
+		 * Use 50M anatop loopback REF_CLK1 for ENET1,
+		 * clear gpr1[13], set gpr1[17].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+				IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+	} else {
+		/*
+		 * Use 50M anatop loopback REF_CLK2 for ENET2,
+		 * clear gpr1[14], set gpr1[18].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+				IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+	}
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+#ifdef CONFIG_DM_VIDEO
+static iomux_v3_cfg_t const lcd_pads[] = {
+	/* Use GPIO for Brightness adjustment, duty cycle = period. */
+	MX6_PAD_GPIO1_IO08__GPIO1_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static int setup_lcd(void)
+{
+	enable_lcdif_clock(LCDIF1_BASE_ADDR, 1);
+
+	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
+
+	/* Reset the LCD */
+	gpio_request(IMX_GPIO_NR(5, 9), "lcd reset");
+	gpio_direction_output(IMX_GPIO_NR(5, 9) , 0);
+	udelay(500);
+	gpio_direction_output(IMX_GPIO_NR(5, 9) , 1);
+
+	/* Set Brightness to high */
+	gpio_request(IMX_GPIO_NR(1, 8), "backlight");
+	gpio_direction_output(IMX_GPIO_NR(1, 8) , 1);
+
+	return 0;
+}
+#else
+static inline int setup_lcd(void) { return 0; }
+#endif
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef	CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+#ifdef CONFIG_USB_EHCI_MX6
+#ifndef CONFIG_DM_USB
+	setup_usb();
+#endif
+#endif
+
+#ifdef CONFIG_FSL_QSPI
+	board_qspi_init();
+#endif
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd1", MAKE_CFGVAL(0x42, 0x20, 0x00, 0x00)},
+	{"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"qspi1", MAKE_CFGVAL(0x10, 0x00, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+	env_set("board_name", "EVK");
+
+	if (is_mx6ul_9x9_evk())
+		env_set("board_rev", "9X9");
+	else
+		env_set("board_rev", "14X14");
+#endif
+
+	setup_lcd();
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	if (is_mx6ul_9x9_evk())
+		puts("Board: MX6UL 9x9 EVK\n");
+	else
+		puts("Board: MX6UL 14x14 EVK\n");
+
+	return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+#include <linux/libfdt.h>
+#include <spl.h>
+#include <asm/arch/mx6-ddr.h>
+
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+#ifdef CONFIG_TARGET_MX6UL_9X9_EVK
+	.grp_ddr_type = 0x00080000,
+#else
+	.grp_ddr_type = 0x000c0000,
+#endif
+};
+
+#ifdef CONFIG_TARGET_MX6UL_9X9_EVK
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000000,
+	.dram_odt1 = 0x00000000,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdqs0 = 0x00003030,
+	.dram_sdqs1 = 0x00003030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x20000000,
+	.p0_mprddlctl = 0x4040484f,
+	.p0_mpwrdlctl = 0x40405247,
+	.mpzqlp2ctl = 0x1b4700c7,
+};
+
+static struct mx6_lpddr2_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 2,
+	.width = 16,
+	.banks = 4,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.trcd_lp = 1500,
+	.trppb_lp = 1500,
+	.trpab_lp = 2000,
+	.trasmin = 4250,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 18,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.walat = 0,
+	.ralat = 5,
+	.mif3_mode = 3,
+	.bi_on = 1,
+	.rtt_wr = 0,        /* LPDDR2 does not need rtt_wr rtt_nom */
+	.rtt_nom = 0,
+	.sde_to_rst = 0,    /* LPDDR2 does not need this field */
+	.rst_to_cke = 0x10, /* JEDEC value for LPDDR2: 200us */
+	.ddr_type = DDR_TYPE_LPDDR2,
+	.refsel = 0,	/* Refresh cycles at 64KHz */
+	.refr = 3,	/* 4 refresh commands per refresh cycle */
+};
+
+#else
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000030,
+	.dram_sdqs0 = 0x00000030,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0 = 0x41570155,
+	.p0_mprddlctl = 0x4040474A,
+	.p0_mpwrdlctl = 0x40405550,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 0,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+	.ddr_type = DDR_TYPE_DDR3,
+	.refsel = 0,	/* Refresh cycles at 64KHz */
+	.refr = 1,	/* 2 refresh commands per refresh cycle */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+#endif
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+void board_init_f(ulong dummy)
+{
+	ccgr_init();
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}
+#endif