GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)
This commit is contained in:
@@ -0,0 +1,12 @@
|
||||
if TARGET_ICONNECT
|
||||
|
||||
config SYS_BOARD
|
||||
default "iconnect"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "iomega"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "iconnect"
|
||||
|
||||
endif
|
||||
@@ -0,0 +1,6 @@
|
||||
ICONNECT BOARD
|
||||
M: Luka Perkov <luka@openwrt.org>
|
||||
S: Maintained
|
||||
F: board/iomega/iconnect/
|
||||
F: include/configs/iconnect.h
|
||||
F: configs/iconnect_defconfig
|
||||
@@ -0,0 +1,7 @@
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# (C) Copyright 2009
|
||||
# Marvell Semiconductor <www.marvell.com>
|
||||
# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
|
||||
|
||||
obj-y := iconnect.o
|
||||
@@ -0,0 +1,92 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright (C) 2009-2012
|
||||
* Wojciech Dubowik <wojciech.dubowik@neratec.com>
|
||||
* Luka Perkov <luka@openwrt.org>
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <miiphy.h>
|
||||
#include <asm/arch/cpu.h>
|
||||
#include <asm/arch/soc.h>
|
||||
#include <asm/arch/mpp.h>
|
||||
#include "iconnect.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
/*
|
||||
* default gpio configuration
|
||||
* There are maximum 64 gpios controlled through 2 sets of registers
|
||||
* the below configuration configures mainly initial LED status
|
||||
*/
|
||||
mvebu_config_gpio(ICONNECT_OE_VAL_LOW,
|
||||
ICONNECT_OE_VAL_HIGH,
|
||||
ICONNECT_OE_LOW, ICONNECT_OE_HIGH);
|
||||
|
||||
/* Multi-Purpose Pins Functionality configuration */
|
||||
static const u32 kwmpp_config[] = {
|
||||
MPP0_NF_IO2,
|
||||
MPP1_NF_IO3,
|
||||
MPP2_NF_IO4,
|
||||
MPP3_NF_IO5,
|
||||
MPP4_NF_IO6,
|
||||
MPP5_NF_IO7,
|
||||
MPP6_SYSRST_OUTn, /* Reset signal */
|
||||
MPP7_GPO,
|
||||
MPP8_TW_SDA, /* I2C */
|
||||
MPP9_TW_SCK, /* I2C */
|
||||
MPP10_UART0_TXD,
|
||||
MPP11_UART0_RXD,
|
||||
MPP12_GPO, /* Reset button */
|
||||
MPP13_SD_CMD,
|
||||
MPP14_SD_D0,
|
||||
MPP15_SD_D1,
|
||||
MPP16_SD_D2,
|
||||
MPP17_SD_D3,
|
||||
MPP18_NF_IO0,
|
||||
MPP19_NF_IO1,
|
||||
MPP20_GE1_0,
|
||||
MPP21_GE1_1,
|
||||
MPP22_GE1_2,
|
||||
MPP23_GE1_3,
|
||||
MPP24_GE1_4,
|
||||
MPP25_GE1_5,
|
||||
MPP26_GE1_6,
|
||||
MPP27_GE1_7,
|
||||
MPP28_GPIO,
|
||||
MPP29_GPIO,
|
||||
MPP30_GE1_10,
|
||||
MPP31_GE1_11,
|
||||
MPP32_GE1_12,
|
||||
MPP33_GE1_13,
|
||||
MPP34_GE1_14,
|
||||
MPP35_GPIO, /* OTB button */
|
||||
MPP36_AUDIO_SPDIFI,
|
||||
MPP37_AUDIO_SPDIFO,
|
||||
MPP38_GPIO,
|
||||
MPP39_TDM_SPI_CS0,
|
||||
MPP40_TDM_SPI_SCK,
|
||||
MPP41_GPIO, /* LED brightness */
|
||||
MPP42_GPIO, /* LED power (blue) */
|
||||
MPP43_GPIO, /* LED power (red) */
|
||||
MPP44_GPIO, /* LED USB 1 */
|
||||
MPP45_GPIO, /* LED USB 2 */
|
||||
MPP46_GPIO, /* LED USB 3 */
|
||||
MPP47_GPIO, /* LED USB 4 */
|
||||
MPP48_GPIO, /* LED OTB */
|
||||
MPP49_GPIO,
|
||||
0
|
||||
};
|
||||
kirkwood_mpp_conf(kwmpp_config, NULL);
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_init(void)
|
||||
{
|
||||
/* adress of boot parameters */
|
||||
gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
|
||||
|
||||
return 0;
|
||||
}
|
||||
@@ -0,0 +1,24 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright (C) 2009-2012
|
||||
* Wojciech Dubowik <wojciech.dubowik@neratec.com>
|
||||
* Luka Perkov <luka@openwrt.org>
|
||||
*/
|
||||
|
||||
#ifndef __ICONNECT_H
|
||||
#define __ICONNECT_H
|
||||
|
||||
#define ICONNECT_OE_LOW (~(1 << 7))
|
||||
#define ICONNECT_OE_HIGH (~(1 << 10))
|
||||
#define ICONNECT_OE_VAL_LOW (0)
|
||||
#define ICONNECT_OE_VAL_HIGH (1 << 10)
|
||||
|
||||
/* PHY related */
|
||||
#define MV88E1116_LED_FCTRL_REG 10
|
||||
#define MV88E1116_CPRSP_CR3_REG 21
|
||||
#define MV88E1116_MAC_CTRL_REG 21
|
||||
#define MV88E1116_PGADR_REG 22
|
||||
#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
|
||||
#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
|
||||
|
||||
#endif /* __ICONNECT_H */
|
||||
@@ -0,0 +1,149 @@
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# (C) Copyright 2009-2012
|
||||
# Wojciech Dubowik <wojciech.dubowik@neratec.com>
|
||||
# Luka Perkov <luka@openwrt.org>
|
||||
# Refer doc/README.kwbimage for more details about how-to configure
|
||||
# and create kirkwood boot image
|
||||
#
|
||||
|
||||
# Boot Media configurations
|
||||
BOOT_FROM nand
|
||||
NAND_ECC_MODE default
|
||||
NAND_PAGE_SIZE 0x0800
|
||||
|
||||
# SOC registers configuration using bootrom header extension
|
||||
# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
|
||||
|
||||
# Configure RGMII-0 interface pad voltage to 1.8V
|
||||
DATA 0xffd100e0 0x1b1b1b9b
|
||||
|
||||
# Dram initalization for SINGLE x16 CL=5 @ 400MHz
|
||||
DATA 0xffd01400 0x43000c30 # DDR Configuration register
|
||||
# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
|
||||
# bit23-14: 0x0,
|
||||
# bit24: 0x1, enable exit self refresh mode on DDR access
|
||||
# bit25: 0x1, required
|
||||
# bit29-26: 0x0,
|
||||
# bit31-30: 0x1,
|
||||
|
||||
DATA 0xffd01404 0x37543000 # DDR Controller Control Low
|
||||
# bit4: 0x0, addr/cmd in smame cycle
|
||||
# bit5: 0x0, clk is driven during self refresh, we don't care for APX
|
||||
# bit6: 0x0, use recommended falling edge of clk for addr/cmd
|
||||
# bit14: 0x0, input buffer always powered up
|
||||
# bit18: 0x1, cpu lock transaction enabled
|
||||
# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
|
||||
# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
|
||||
# bit30-28: 0x3, required
|
||||
# bit31: 0x0, no additional STARTBURST delay
|
||||
|
||||
DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
|
||||
# bit3-0: TRAS lsbs
|
||||
# bit7-4: TRCD
|
||||
# bit11-8: TRP
|
||||
# bit15-12: TWR
|
||||
# bit19-16: TWTR
|
||||
# bit20: TRAS msb
|
||||
# bit23-21: 0x0
|
||||
# bit27-24: TRRD
|
||||
# bit31-28: TRTP
|
||||
|
||||
DATA 0xffd0140c 0x00000a33 # DDR Timing (High)
|
||||
# bit6-0: TRFC
|
||||
# bit8-7: TR2R
|
||||
# bit10-9: TR2W
|
||||
# bit12-11: TW2W
|
||||
# bit31-13: 0x0, required
|
||||
|
||||
DATA 0xffd01410 0x000000cc # DDR Address Control
|
||||
# bit1-0: 00, Cs0width (x8)
|
||||
# bit3-2: 11, Cs0size (1Gb)
|
||||
# bit5-4: 00, Cs1width (x8)
|
||||
# bit7-6: 11, Cs1size (1Gb)
|
||||
# bit9-8: 00, Cs2width (nonexistent)
|
||||
# bit11-10: 00, Cs2size (nonexistent)
|
||||
# bit13-12: 00, Cs3width (nonexistent)
|
||||
# bit15-14: 00, Cs3size (nonexistent)
|
||||
# bit16: 0, Cs0AddrSel
|
||||
# bit17: 0, Cs1AddrSel
|
||||
# bit18: 0, Cs2AddrSel
|
||||
# bit19: 0, Cs3AddrSel
|
||||
# bit31-20: 0x0, required
|
||||
|
||||
DATA 0xffd01414 0x00000000 # DDR Open Pages Control
|
||||
# bit0: 0, OpenPage enabled
|
||||
# bit31-1: 0x0, required
|
||||
|
||||
DATA 0xffd01418 0x00000000 # DDR Operation
|
||||
# bit3-0: 0x0, DDR cmd
|
||||
# bit31-4: 0x0, required
|
||||
|
||||
DATA 0xffd0141c 0x00000c52 # DDR Mode
|
||||
# bit2-0: 0x2, BurstLen=2 required
|
||||
# bit3: 0x0, BurstType=0 required
|
||||
# bit6-4: 0x4, CL=5
|
||||
# bit7: 0x0, TestMode=0 normal
|
||||
# bit8: 0x0, DLL reset=0 normal
|
||||
# bit11-9: 0x6, auto-precharge write recovery
|
||||
# bit12: 0x0, PD must be zero
|
||||
# bit31-13: 0x0, required
|
||||
|
||||
DATA 0xffd01420 0x00000040 # DDR Extended Mode
|
||||
# bit0: 0, DDR DLL enabled
|
||||
# bit1: 0, DDR drive strenght normal
|
||||
# bit2: 0, DDR ODT control lsd (disabled)
|
||||
# bit5-3: 0x0, required
|
||||
# bit6: 1, DDR ODT control msb, (disabled)
|
||||
# bit9-7: 0x0, required
|
||||
# bit10: 0, differential DQS enabled
|
||||
# bit11: 0, required
|
||||
# bit12: 0, DDR output buffer enabled
|
||||
# bit31-13: 0x0, required
|
||||
|
||||
DATA 0xffd01424 0x0000f17f # DDR Controller Control High
|
||||
# bit2-0: 0x7, required
|
||||
# bit3: 0x1, MBUS Burst Chop disabled
|
||||
# bit6-4: 0x7, required
|
||||
# bit7: 0x0,
|
||||
# bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
|
||||
# bit9: 0x0, no half clock cycle addition to dataout
|
||||
# bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals
|
||||
# bit11: 0x0, 1/4 clock cycle skew disabled for write mesh
|
||||
# bit15-12: 0xf, required
|
||||
# bit31-16: 0x0, required
|
||||
|
||||
DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
|
||||
DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
|
||||
|
||||
DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0
|
||||
DATA 0xffd01504 0x0ffffff1 # CS[0]n Size
|
||||
# bit0: 0x1, Window enabled
|
||||
# bit1: 0x0, Write Protect disabled
|
||||
# bit3-2: 0x0, CS0 hit selected
|
||||
# bit23-4: 0xfffff, required
|
||||
# bit31-24: 0x0f, Size (i.e. 256MB)
|
||||
|
||||
DATA 0xffd01508 0x00000000 # CS[1]n Base address to 256Mb
|
||||
DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled
|
||||
|
||||
DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled
|
||||
DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled
|
||||
|
||||
DATA 0xffd01494 0x00030000 # DDR ODT Control (Low)
|
||||
# bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1
|
||||
# bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0
|
||||
# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
|
||||
# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
|
||||
|
||||
DATA 0xffd01498 0x00000000 # DDR ODT Control (High)
|
||||
# bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above
|
||||
# bit3-2: 0x1, ODT1 active NEVER!
|
||||
# bit31-4: 0x0, required
|
||||
|
||||
DATA 0xffd0149c 0x0000e803 # CPU ODT Control
|
||||
DATA 0xffd01480 0x00000001 # DDR Initialization Control
|
||||
# bit0: 0x1, enable DDR init upon this register write
|
||||
|
||||
# End of Header extension
|
||||
DATA 0x0 0x0
|
||||
Reference in New Issue
Block a user