GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/phy/no-op.txt

@@ -0,0 +1,16 @@
+NOP PHY driver
+
+This driver is used to stub PHY operations in a driver (USB, SATA).
+This is useful when the 'client' driver (USB, SATA, ...) uses the PHY framework
+and there is no actual PHY harwdare to drive.
+
+Required properties:
+- compatible     : must contain "nop-phy"
+- #phy-cells     : must contain <0>
+
+Example:
+
+nop_phy {
+	compatible = "nop-phy";
+	#phy-cells = <0>;
+};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/phy/phy-mtk-tphy.txt

@@ -0,0 +1,86 @@
+MediaTek T-PHY binding
+--------------------------
+
+T-phy controller supports physical layer functionality for a number of
+controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA.
+
+Required properties (controller (parent) node):
+ - compatible	: should be one of
+		  "mediatek,generic-tphy-v1"
+ - clocks	: (deprecated, use port's clocks instead) a list of phandle +
+		  clock-specifier pairs, one for each entry in clock-names
+ - clock-names	: (deprecated, use port's one instead) must contain
+		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+Required nodes	: a sub-node is required for each port the controller
+		  provides. Address range information including the usual
+		  'reg' property is used inside these nodes to describe
+		  the controller's topology.
+
+Optional properties (controller (parent) node):
+ - reg		: offset and length of register shared by multiple ports,
+		  exclude port's private register.
+ - mediatek,src-ref-clk-mhz	: frequency of reference clock for slew rate
+		  calibrate
+ - mediatek,src-coef	: coefficient for slew rate calibrate, depends on
+		  SoC process
+
+Required properties (port (child) node):
+- reg		: address and length of the register set for the port.
+- clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+- clock-names	: must contain
+		  "ref": 48M reference clock for HighSpeed analog phy; and 26M
+			reference clock for SuperSpeed analog phy, sometimes is
+			24M, 25M or 27M, depended on platform.
+- #phy-cells	: should be 1 (See second example)
+		  cell after port phandle is phy type from:
+			- PHY_TYPE_USB2
+			- PHY_TYPE_USB3
+			- PHY_TYPE_PCIE
+			- PHY_TYPE_SATA
+
+Example:
+
+	u3phy2: usb-phy@1a244000 {
+		compatible = "mediatek,generic-tphy-v1";
+		reg = <0x1a244000 0x0700>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		status = "disabled";
+
+		u2port1: usb-phy@1a244800 {
+			reg = <0x1a244800 0x0100>;
+			clocks = <&topckgen CLK_TOP_USB_PHY48M>;
+			clock-names = "ref";
+			#phy-cells = <1>;
+			status = "okay";
+		};
+
+		u3port1: usb-phy@1a244900 {
+			reg = <0x1a244900 0x0700>;
+			clocks = <&clk26m>;
+			clock-names = "ref";
+			#phy-cells = <1>;
+			status = "okay";
+		};
+	};
+
+Specifying phy control of devices
+---------------------------------
+
+Device nodes should specify the configuration required in their "phys"
+property, containing a phandle to the phy port node and a device type;
+phy-names for each port are optional.
+
+Example:
+
+#include <dt-bindings/phy/phy.h>
+
+usb30: usb@11270000 {
+	...
+	phys = <&u2port0 PHY_TYPE_USB2>, <&u3port0 PHY_TYPE_USB3>;
+	phy-names = "usb2-0", "usb3-0";
+	...
+};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/phy/phy-stih407-usb.txt

@@ -0,0 +1,24 @@
+ST STiH407 USB PHY controller
+
+This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3
+host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics.
+
+Required properties:
+- compatible		: should be "st,stih407-usb2-phy"
+- st,syscfg		: phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets
+- resets		: list of phandle and reset specifier pairs. There should be two entries, one
+			  for the whole phy and one for the port
+- reset-names		: list of reset signal names. Should be "global" and "port"
+See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
+See: Documentation/devicetree/bindings/reset/reset.txt
+
+Example:
+
+usb2_picophy0: usbpicophy {
+	compatible	= "st,stih407-usb2-phy";
+	#phy-cells	= <0>;
+	st,syscfg	= <&syscfg_core 0x100 0xf4>;
+	resets		= <&softreset STIH407_PICOPHY_SOFTRESET>,
+			  <&picophyreset STIH407_PICOPHY0_RESET>;
+	reset-names	= "global", "port";
+};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/phy/phy-stm32-usbphyc.txt

@@ -0,0 +1,73 @@
+STMicroelectronics STM32 USB HS PHY controller
+
+The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
+switch. It controls PHY configuration and status, and the UTMI+ switch that
+selects either OTG or HOST controller for the second PHY port. It also sets
+PLL configuration.
+
+USBPHYC
+      |_ PLL
+      |
+      |_ PHY port#1 _________________ HOST controller
+      |                    _                 |
+      |                  / 1|________________|
+      |_ PHY port#2 ----|   |________________
+      |                  \_0|                |
+      |_ UTMI switch_______|          OTG controller
+
+
+Phy provider node
+=================
+
+Required properties:
+- compatible: must be "st,stm32mp1-usbphyc"
+- reg: address and length of the usb phy control register set
+- clocks: phandle + clock specifier for the PLL phy clock
+- vdda1v1-supply: phandle to the regulator providing 1V1 power to the PHY
+- vdda1v8-supply: phandle to the regulator providing 1V8 power to the PHY
+- #address-cells: number of address cells for phys sub-nodes, must be <1>
+- #size-cells: number of size cells for phys sub-nodes, must be <0>
+
+Optional properties:
+- assigned-clocks: phandle + clock specifier for the PLL phy clock
+- assigned-clock-parents: the PLL phy clock parent
+- resets: phandle + reset specifier
+
+Required nodes: one sub-node per port the controller provides.
+
+Phy sub-nodes
+==============
+
+Required properties:
+- reg: phy port index
+- phy-supply: phandle to the regulator providing 3V3 power to the PHY,
+	      see phy-bindings.txt in the same directory.
+- #phy-cells: see phy-bindings.txt in the same directory, must be <0> for PHY
+  port#1 and must be <1> for PHY port#2, to select USB controller
+
+
+Example:
+		usbphyc: usb-phy@5a006000 {
+			compatible = "st,stm32mp1-usbphyc";
+			reg = <0x5a006000 0x1000>;
+			clocks = <&rcc_clk USBPHY_K>;
+			resets = <&rcc_rst USBPHY_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usbphyc_port0: usb-phy@0 {
+				reg = <0>;
+				phy-supply = <&vdd_usb>;
+				vdda1v1-supply = <&reg11>;
+				vdda1v8-supply = <&reg18>
+				#phy-cells = <0>;
+			};
+
+			usbphyc_port1: usb-phy@1 {
+				reg = <1>;
+				phy-supply = <&vdd_usb>;
+				vdda1v1-supply = <&reg11>;
+				vdda1v8-supply = <&reg18>
+				#phy-cells = <1>;
+			};
+		};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/phy/sun4i-usb-phy.txt

@@ -0,0 +1,65 @@
+Allwinner sun4i USB PHY
+-----------------------
+
+Required properties:
+- compatible : should be one of
+  * allwinner,sun4i-a10-usb-phy
+  * allwinner,sun5i-a13-usb-phy
+  * allwinner,sun6i-a31-usb-phy
+  * allwinner,sun7i-a20-usb-phy
+  * allwinner,sun8i-a23-usb-phy
+  * allwinner,sun8i-a33-usb-phy
+  * allwinner,sun8i-a83t-usb-phy
+  * allwinner,sun8i-h3-usb-phy
+  * allwinner,sun8i-v3s-usb-phy
+  * allwinner,sun50i-a64-usb-phy
+- reg : a list of offset + length pairs
+- reg-names :
+  * "phy_ctrl"
+  * "pmu0" for H3, V3s and A64
+  * "pmu1"
+  * "pmu2" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3
+  * "pmu3" for sun8i-h3
+- #phy-cells : from the generic phy bindings, must be 1
+- clocks : phandle + clock specifier for the phy clocks
+- clock-names :
+  * "usb_phy" for sun4i, sun5i or sun7i
+  * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
+  * "usb0_phy", "usb1_phy" for sun8i
+  * "usb0_phy", "usb1_phy", "usb2_phy" and "usb2_hsic_12M" for sun8i-a83t
+  * "usb0_phy", "usb1_phy", "usb2_phy" and "usb3_phy" for sun8i-h3
+- resets : a list of phandle + reset specifier pairs
+- reset-names :
+  * "usb0_reset"
+  * "usb1_reset"
+  * "usb2_reset" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3
+  * "usb3_reset" for sun8i-h3
+
+Optional properties:
+- usb0_id_det-gpios : gpio phandle for reading the otg id pin value
+- usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus
+- usb0_vbus_power-supply: power-supply phandle for usb0 vbus presence detect
+- usb0_vbus-supply : regulator phandle for controller usb0 vbus
+- usb1_vbus-supply : regulator phandle for controller usb1 vbus
+- usb2_vbus-supply : regulator phandle for controller usb2 vbus
+- usb3_vbus-supply : regulator phandle for controller usb3 vbus
+
+Example:
+	usbphy: phy@01c13400 {
+		#phy-cells = <1>;
+		compatible = "allwinner,sun4i-a10-usb-phy";
+		/* phy base regs, phy1 pmu reg, phy2 pmu reg */
+		reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>;
+		reg-names = "phy_ctrl", "pmu1", "pmu2";
+		clocks = <&usb_clk 8>;
+		clock-names = "usb_phy";
+		resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>;
+		reset-names = "usb0_reset", "usb1_reset", "usb2_reset";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+		usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
+		usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */
+		usb0_vbus-supply = <&reg_usb0_vbus>;
+		usb1_vbus-supply = <&reg_usb1_vbus>;
+		usb2_vbus-supply = <&reg_usb2_vbus>;
+	};