GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/usb/dwc2.txt

@@ -0,0 +1,58 @@
+Platform DesignWare HS OTG USB 2.0 controller
+-----------------------------------------------------
+
+Required properties:
+- compatible : One of:
+  - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
+  - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC.
+  - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
+  - "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc;
+  - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
+  - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
+  - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
+  - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
+  - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
+  - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
+  - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
+  - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
+  - snps,dwc2: A generic DWC2 USB controller with default parameters.
+  - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs
+  configured in FS mode;
+  - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs
+  configured in HS mode;
+  - "st,stm32f7-hsotg": The DWC2 USB HS controller instance in STM32F7 SoCs
+    configured in HS mode;
+- reg : Should contain 1 register range (address and length)
+- interrupts : Should contain 1 interrupt
+- clocks: clock provider specifier
+- clock-names: shall be "otg"
+Refer to clk/clock-bindings.txt for generic clock consumer properties
+
+Optional properties:
+- phys: phy provider specifier
+- phy-names: shall be "usb2-phy"
+Refer to phy/phy-bindings.txt for generic phy consumer properties
+- dr_mode: shall be one of "host", "peripheral" and "otg"
+  Refer to usb/generic.txt
+- g-rx-fifo-size: size of rx fifo size in gadget mode.
+- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode.
+- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode.
+- usb33d-supply: external VBUS and ID sensing comparators supply, in order to
+  perform OTG operation, used on STM32MP1 SoCs.
+- u-boot,force-b-session-valid: force B-peripheral session instead of relying on
+  VBUS sensing (only valid when dr_mode = "peripheral" and for u-boot).
+
+Deprecated properties:
+- g-use-dma: gadget DMA mode is automatically detected
+
+Example:
+
+        usb@101c0000 {
+                compatible = "ralink,rt3050-usb, snps,dwc2";
+                reg = <0x101c0000 40000>;
+                interrupts = <18>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+        };

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/usb/dwc3-st.txt

@@ -0,0 +1,60 @@
+ST DWC3 glue logic
+
+This file documents the parameters for the dwc3-st driver.
+This driver controls the glue logic used to configure the dwc3 core on
+STiH407 based platforms.
+
+Required properties:
+ - compatible	: must be "st,stih407-dwc3"
+ - reg		: glue logic base address and USB syscfg ctrl register offset
+ - reg-names	: should be "reg-glue" and "syscfg-reg"
+ - st,syscon	: should be phandle to system configuration node which
+		  encompasses the glue registers
+ - resets	: list of phandle and reset specifier pairs. There should be two entries, one
+		  for the powerdown and softreset lines of the usb3 IP
+ - reset-names	: list of reset signal names. Names should be "powerdown" and "softreset"
+
+ - #address-cells, #size-cells : should be '1' if the device has sub-nodes
+   with 'reg' property
+
+ - pinctl-names	: A pinctrl state named "default" must be defined
+
+ - pinctrl-0	: Pin control group
+
+ - ranges	: allows valid 1:1 translation between child's address space and
+		  parent's address space
+
+Sub-nodes:
+The dwc3 core should be added as subnode to ST DWC3 glue as shown in the
+example below.
+
+NB: The dr_mode property is NOT optional for this driver, as the default value
+is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are
+either "host" or "device".
+
+Example:
+
+st_dwc3: dwc3@8f94000 {
+	status		= "disabled";
+	compatible	= "st,stih407-dwc3";
+	reg		= <0x08f94000 0x1000>, <0x110 0x4>;
+	reg-names	= "reg-glue", "syscfg-reg";
+	st,syscfg	= <&syscfg_core>;
+	resets		= <&powerdown STIH407_USB3_POWERDOWN>,
+			  <&softreset STIH407_MIPHY2_SOFTRESET>;
+	reset-names	= "powerdown", "softreset";
+	#address-cells	= <1>;
+	#size-cells	= <1>;
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_usb3>;
+	ranges;
+
+	dwc3: dwc3@9900000 {
+		compatible	= "snps,dwc3";
+		reg		= <0x09900000 0x100000>;
+		interrupts	= <GIC_SPI 155 IRQ_TYPE_NONE>;
+		dr_mode		= "host";
+		phy-names	= "usb2-phy", "usb3-phy";
+		phys		= <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>;
+	};
+};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/usb/ehci-msm.txt

@@ -0,0 +1,10 @@
+Chipidea EHCI controller (part of OTG controller) used on Qualcomm devices.
+
+Required properties:
+- compatible: must be "qcom,ehci-host"
+- reg: start address and size of the registers
+
+ehci@78d9000 {
+	compatible = "qcom,ehci-host";
+	reg = <0x78d9000 0x400>;
+};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/usb/marvell.xhci-usb.txt

@@ -0,0 +1,28 @@
+Marvell SOC USB controllers
+
+This controller is integrated in Armada 3700/8K.
+It uses the same properties as a generic XHCI host controller
+
+Required properties :
+ - compatible: should be one or more of:
+   - "marvell,armada3700-xhci", "generic-xhci" for Armada 37xx SoCs
+   - "marvell,armada-8k-xhci", "generic-xhci" for Armada A8K SoCs
+ - reg: should contain address and length of the standard XHCI
+   register set for the device.
+ - interrupts: one XHCI interrupt should be described here.
+
+Optional properties:
+ - clocks: phandle to system controller clock driving this unit
+ - vbus-supply : If present, specifies the fixed regulator to be turned on
+   for providing power to the USB VBUS rail.
+
+Example:
+	cpm_usb3_0: usb3@500000 {
+		compatible = "marvell,armada-8k-xhci",
+			     "generic-xhci";
+		reg = <0x500000 0x4000>;
+		interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpm_syscon0 1 22>;
+		vbus-supply = <&reg_usb3h0_vbus>;
+		status = "disabled";
+	};

source/bootloader/u-boot-2020.01/doc/device-tree-bindings/usb/tegra-usb.txt

@@ -0,0 +1,25 @@
+Tegra SOC USB controllers
+
+The device node for a USB controller that is part of a Tegra
+SOC is as described in the document "Open Firmware Recommended
+Practice : Universal Serial Bus" with the following modifications
+and additions :
+
+Required properties :
+ - compatible : Should be "nvidia,tegra20-ehci" for USB controllers
+   used in host mode.
+ - phy_type : Should be one of "ulpi" or "utmi".
+ - nvidia,vbus-gpio : If present, specifies a gpio that needs to be
+   activated for the bus to be powered.
+
+Optional properties:
+  - dr_mode : dual role mode. Indicates the working mode for
+    nvidia,tegra20-ehci compatible controllers.  Can be "host", "peripheral",
+    or "otg".  Default to "host" if not defined for backward compatibility.
+      host means this is a host controller
+      peripheral means it is device controller
+      otg means it can operate as either ("on the go")
+  - nvidia,has-legacy-mode : boolean indicates whether this controller can
+    operate in legacy mode (as APX 2500 / 2600). In legacy mode some
+    registers are accessed through the APB_MISC base address instead of
+    the USB controller.