GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)
This commit is contained in:
@@ -0,0 +1,335 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright (C) 2009-2010 Freescale Semiconductor, Inc.
|
||||
* Copyright (C) 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com
|
||||
*
|
||||
*/
|
||||
|
||||
#ifndef __CONFIG_H
|
||||
#define __CONFIG_H
|
||||
|
||||
/*
|
||||
* High Level Configuration Options
|
||||
*/
|
||||
#define CONFIG_E300 1 /* E300 family */
|
||||
|
||||
#ifdef CONFIG_MMC
|
||||
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC83xx_ESDHC_ADDR
|
||||
#define CONFIG_SYS_FSL_ESDHC_USE_PIO
|
||||
#endif
|
||||
|
||||
/*
|
||||
* On-board devices
|
||||
*
|
||||
* TSEC1 is SoC TSEC
|
||||
* TSEC2 is VSC switch
|
||||
*/
|
||||
#define CONFIG_TSEC1
|
||||
#define CONFIG_VSC7385_ENET
|
||||
|
||||
/*
|
||||
* SERDES
|
||||
*/
|
||||
#define CONFIG_FSL_SERDES
|
||||
#define CONFIG_FSL_SERDES1 0xe3000
|
||||
|
||||
/*
|
||||
* DDR Setup
|
||||
*/
|
||||
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory */
|
||||
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
|
||||
#define CONFIG_SYS_DDRCDR_VALUE (DDRCDR_EN \
|
||||
| DDRCDR_PZ_LOZ \
|
||||
| DDRCDR_NZ_LOZ \
|
||||
| DDRCDR_ODT \
|
||||
| DDRCDR_Q_DRN)
|
||||
/* 0x7b880001 */
|
||||
/*
|
||||
* Manually set up DDR parameters
|
||||
* consist of two chips HY5PS12621BFP-C4 from HYNIX
|
||||
*/
|
||||
|
||||
#define CONFIG_SYS_DDR_SIZE 128 /* MB */
|
||||
|
||||
#define CONFIG_SYS_DDR_CS0_BNDS 0x00000007
|
||||
#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \
|
||||
| CSCONFIG_ODT_RD_NEVER \
|
||||
| CSCONFIG_ODT_WR_ONLY_CURRENT \
|
||||
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
|
||||
/* 0x80010102 */
|
||||
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
|
||||
#define CONFIG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) \
|
||||
| (0 << TIMING_CFG0_WRT_SHIFT) \
|
||||
| (0 << TIMING_CFG0_RRT_SHIFT) \
|
||||
| (0 << TIMING_CFG0_WWT_SHIFT) \
|
||||
| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
|
||||
| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
|
||||
| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
|
||||
| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
|
||||
/* 0x00220802 */
|
||||
#define CONFIG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) \
|
||||
| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
|
||||
| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
|
||||
| (5 << TIMING_CFG1_CASLAT_SHIFT) \
|
||||
| (6 << TIMING_CFG1_REFREC_SHIFT) \
|
||||
| (2 << TIMING_CFG1_WRREC_SHIFT) \
|
||||
| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
|
||||
| (2 << TIMING_CFG1_WRTORD_SHIFT))
|
||||
/* 0x27256222 */
|
||||
#define CONFIG_SYS_DDR_TIMING_2 ((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
|
||||
| (4 << TIMING_CFG2_CPO_SHIFT) \
|
||||
| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
|
||||
| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
|
||||
| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
|
||||
| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
|
||||
| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
|
||||
/* 0x121048c5 */
|
||||
#define CONFIG_SYS_DDR_INTERVAL ((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
|
||||
| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
|
||||
/* 0x03600100 */
|
||||
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN \
|
||||
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
|
||||
| SDRAM_CFG_DBW_32)
|
||||
/* 0x43080000 */
|
||||
|
||||
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 /* 1 posted refresh */
|
||||
#define CONFIG_SYS_DDR_MODE ((0x0448 << SDRAM_MODE_ESD_SHIFT) \
|
||||
| (0x0232 << SDRAM_MODE_SD_SHIFT))
|
||||
/* ODT 150ohm CL=3, AL=1 on SDRAM */
|
||||
#define CONFIG_SYS_DDR_MODE2 0x00000000
|
||||
|
||||
/*
|
||||
* Memory test
|
||||
*/
|
||||
#define CONFIG_SYS_MEMTEST_START 0x00001000 /* memtest region */
|
||||
#define CONFIG_SYS_MEMTEST_END 0x07f00000
|
||||
|
||||
/*
|
||||
* The reserved memory
|
||||
*/
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
|
||||
|
||||
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
|
||||
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
|
||||
|
||||
/*
|
||||
* Initial RAM Base Address Setup
|
||||
*/
|
||||
#define CONFIG_SYS_INIT_RAM_LOCK 1
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
|
||||
#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
|
||||
#define CONFIG_SYS_GBL_DATA_OFFSET \
|
||||
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
||||
|
||||
/*
|
||||
* FLASH on the Local Bus
|
||||
*/
|
||||
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
|
||||
|
||||
#define CONFIG_SYS_FLASH_BASE 0xFE000000 /* FLASH base address */
|
||||
#define CONFIG_SYS_FLASH_SIZE 8 /* FLASH size is 8M */
|
||||
|
||||
|
||||
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
|
||||
/* 127 64KB sectors and 8 8KB top sectors per device */
|
||||
#define CONFIG_SYS_MAX_FLASH_SECT 135
|
||||
|
||||
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
||||
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
||||
|
||||
/*
|
||||
* NAND Flash on the Local Bus
|
||||
*/
|
||||
#define CONFIG_SYS_NAND_BASE 0xE0600000 /* 0xE0600000 */
|
||||
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024) /* 0x00008000 */
|
||||
/* 0xFFFF8396 */
|
||||
|
||||
#ifdef CONFIG_VSC7385_ENET
|
||||
#define CONFIG_TSEC2
|
||||
/* VSC7385 Base address on CS2 */
|
||||
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
|
||||
#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
|
||||
/* 0xFFFE09FF */
|
||||
/* The flash address and size of the VSC7385 firmware image */
|
||||
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
|
||||
#define CONFIG_VSC7385_IMAGE_SIZE 8192
|
||||
#endif
|
||||
/*
|
||||
* Serial Port
|
||||
*/
|
||||
#define CONFIG_SYS_NS16550_SERIAL
|
||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
||||
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
|
||||
|
||||
#define CONFIG_SYS_BAUDRATE_TABLE \
|
||||
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
||||
|
||||
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
|
||||
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)
|
||||
|
||||
/* I2C */
|
||||
#define CONFIG_SYS_I2C
|
||||
#define CONFIG_SYS_I2C_FSL
|
||||
#define CONFIG_SYS_FSL_I2C_SPEED 400000
|
||||
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
|
||||
#define CONFIG_SYS_FSL_I2C2_SPEED 400000
|
||||
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
|
||||
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x51} }
|
||||
|
||||
/*
|
||||
* SPI on header J8
|
||||
*
|
||||
* WARNING: enabling this will break TSEC2 (connected to the Vitesse switch)
|
||||
* due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins.
|
||||
*/
|
||||
#ifdef CONFIG_MPC8XXX_SPI
|
||||
#define CONFIG_USE_SPIFLASH
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Board info - revision and where boot from
|
||||
*/
|
||||
#define CONFIG_SYS_I2C_PCF8574A_ADDR 0x39
|
||||
|
||||
/*
|
||||
* Config on-board RTC
|
||||
*/
|
||||
#define CONFIG_RTC_DS1337 /* ds1339 on board, use ds1337 rtc via i2c */
|
||||
#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /* at address 0x68 */
|
||||
|
||||
/*
|
||||
* General PCI
|
||||
* Addresses are mapped 1-1.
|
||||
*/
|
||||
#define CONFIG_SYS_PCIE1_BASE 0xA0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_BASE 0xA0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
|
||||
#define CONFIG_SYS_PCIE1_CFG_BASE 0xB0000000
|
||||
#define CONFIG_SYS_PCIE1_CFG_SIZE 0x01000000
|
||||
#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
|
||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xB1000000
|
||||
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
|
||||
|
||||
/* enable PCIE clock */
|
||||
#define CONFIG_SYS_SCCR_PCIEXP1CM 1
|
||||
|
||||
#define CONFIG_PCI_INDIRECT_BRIDGE
|
||||
#define CONFIG_PCIE
|
||||
|
||||
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
|
||||
#define CONFIG_83XX_GENERIC_PCIE_REGISTER_HOSES 1
|
||||
|
||||
/*
|
||||
* TSEC
|
||||
*/
|
||||
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
|
||||
#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
|
||||
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
|
||||
#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
|
||||
|
||||
/*
|
||||
* TSEC ethernet configuration
|
||||
*/
|
||||
#define CONFIG_TSEC1_NAME "eTSEC0"
|
||||
#define CONFIG_TSEC2_NAME "eTSEC1"
|
||||
#define TSEC1_PHY_ADDR 2
|
||||
#define TSEC2_PHY_ADDR 1
|
||||
#define TSEC1_PHYIDX 0
|
||||
#define TSEC2_PHYIDX 0
|
||||
#define TSEC1_FLAGS TSEC_GIGABIT
|
||||
#define TSEC2_FLAGS TSEC_GIGABIT
|
||||
|
||||
/* Options are: eTSEC[0-1] */
|
||||
#define CONFIG_ETHPRIME "eTSEC0"
|
||||
|
||||
/*
|
||||
* Environment
|
||||
*/
|
||||
|
||||
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
||||
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
|
||||
|
||||
/*
|
||||
* BOOTP options
|
||||
*/
|
||||
#define CONFIG_BOOTP_BOOTFILESIZE
|
||||
|
||||
/*
|
||||
* Command line configuration.
|
||||
*/
|
||||
|
||||
/*
|
||||
* Miscellaneous configurable options
|
||||
*/
|
||||
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
||||
|
||||
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
||||
|
||||
/* Boot Argument Buffer Size */
|
||||
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
|
||||
|
||||
/*
|
||||
* For booting Linux, the board info and command line data
|
||||
* have to be in the first 256 MB of memory, since this is
|
||||
* the maximum mapped by the Linux kernel during initialization.
|
||||
*/
|
||||
#define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */
|
||||
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
||||
|
||||
/*
|
||||
* Environment Configuration
|
||||
*/
|
||||
|
||||
#define CONFIG_ENV_OVERWRITE
|
||||
|
||||
#if defined(CONFIG_TSEC_ENET)
|
||||
#define CONFIG_HAS_ETH0
|
||||
#define CONFIG_HAS_ETH1
|
||||
#endif
|
||||
|
||||
#define CONFIG_LOADADDR 800000 /* default location for tftp and bootm */
|
||||
|
||||
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||
"netdev=eth0\0" \
|
||||
"consoledev=ttyS0\0" \
|
||||
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
||||
"nfsroot=${serverip}:${rootpath}\0" \
|
||||
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
||||
"addip=setenv bootargs ${bootargs} " \
|
||||
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
||||
":${hostname}:${netdev}:off panic=1\0" \
|
||||
"addtty=setenv bootargs ${bootargs}" \
|
||||
" console=${consoledev},${baudrate}\0" \
|
||||
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
|
||||
"addmisc=setenv bootargs ${bootargs}\0" \
|
||||
"kernel_addr=FE080000\0" \
|
||||
"fdt_addr=FE280000\0" \
|
||||
"ramdisk_addr=FE290000\0" \
|
||||
"u-boot=mpc8308rdb/u-boot.bin\0" \
|
||||
"kernel_addr_r=1000000\0" \
|
||||
"fdt_addr_r=C00000\0" \
|
||||
"hostname=mpc8308rdb\0" \
|
||||
"bootfile=mpc8308rdb/uImage\0" \
|
||||
"fdtfile=mpc8308rdb/mpc8308rdb.dtb\0" \
|
||||
"rootpath=/opt/eldk-4.2/ppc_6xx\0" \
|
||||
"flash_self=run ramargs addip addtty addmtd addmisc;" \
|
||||
"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
|
||||
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
|
||||
"bootm ${kernel_addr} - ${fdt_addr}\0" \
|
||||
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
|
||||
"tftp ${fdt_addr_r} ${fdtfile};" \
|
||||
"run nfsargs addip addtty addmtd addmisc;" \
|
||||
"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
|
||||
"bootcmd=run flash_self\0" \
|
||||
"load=tftp ${loadaddr} ${u-boot}\0" \
|
||||
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
|
||||
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
|
||||
" +${filesize};cp.b ${fileaddr} " \
|
||||
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
|
||||
"upd=run load update\0" \
|
||||
|
||||
#endif /* __CONFIG_H */
|
||||
Reference in New Issue
Block a user