GK SDK 源码库: XMIPCLinuxV100R005C00SPC030 (kernel/tools/open_source excluded)

source/bootloader/u-boot-2020.01/include/configs/MigoR.h

@@ -0,0 +1,87 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuation settings for the Renesas Solutions Migo-R board
+ *
+ * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
+ */
+
+#ifndef __MIGO_R_H
+#define __MIGO_R_H
+
+#define CONFIG_CPU_SH7722	1
+
+#define CONFIG_DISPLAY_BOARDINFO
+
+/* SMC9111 */
+#define CONFIG_SMC91111
+#define CONFIG_SMC91111_BASE    (0xB0000000)
+
+/* MEMORY */
+#define MIGO_R_SDRAM_BASE	(0x8C000000)
+#define MIGO_R_FLASH_BASE_1	(0xA0000000)
+#define MIGO_R_FLASH_BANK_SIZE	(64 * 1024 * 1024)
+
+#define CONFIG_SYS_PBSIZE		256		/* Buffer size for Console output */
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 115200 }	/* List of legal baudrate settings for this board */
+
+/* SCIF */
+#define CONFIG_CONS_SCIF0	1
+
+#define CONFIG_SYS_MEMTEST_START	(MIGO_R_SDRAM_BASE)
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + (60 * 1024 * 1024))
+
+/* Enable alternate, more extensive, memory test */
+/* Scratch address used by the alternate memory test */
+#undef  CONFIG_SYS_MEMTEST_SCRATCH
+
+/* Enable temporary baudrate change while serial download */
+#undef  CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_SYS_SDRAM_BASE	(MIGO_R_SDRAM_BASE)
+/* maybe more, but if so u-boot doesn't know about it... */
+#define CONFIG_SYS_SDRAM_SIZE	(64 * 1024 * 1024)
+/* default load address for scripts ?!? */
+#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_SDRAM_BASE + 16 * 1024 * 1024)
+
+/* Address of u-boot image in Flash (NOT run time address in SDRAM) ?!? */
+#define CONFIG_SYS_MONITOR_BASE	(MIGO_R_FLASH_BASE_1)
+/* Monitor size */
+#define CONFIG_SYS_MONITOR_LEN	(128 * 1024)
+/* Size of DRAM reserved for malloc() use */
+#define CONFIG_SYS_MALLOC_LEN	(256 * 1024)
+#define CONFIG_SYS_BOOTMAPSZ	(8 * 1024 * 1024)
+
+/* FLASH */
+#undef  CONFIG_SYS_FLASH_QUIET_TEST
+/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+/* Physical start address of Flash memory */
+#define CONFIG_SYS_FLASH_BASE	(MIGO_R_FLASH_BASE_1)
+/* Max number of sectors on each Flash chip */
+#define CONFIG_SYS_MAX_FLASH_SECT	512
+
+/* if you use all NOR Flash , you change dip-switch. Please see MIGO_R01 Manual. */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE + (0 * MIGO_R_FLASH_BANK_SIZE) }
+
+/* Timeout for Flash erase operations (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	(3 * 1000)
+/* Timeout for Flash write operations (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	(3 * 1000)
+/* Timeout for Flash set sector lock bit operations (in ms) */
+#define CONFIG_SYS_FLASH_LOCK_TOUT	(3 * 1000)
+/* Timeout for Flash clear lock bit operations (in ms) */
+#define CONFIG_SYS_FLASH_UNLOCK_TOUT	(3 * 1000)
+
+/* Use hardware flash sectors protection instead of U-Boot software protection */
+#undef  CONFIG_SYS_DIRECT_FLASH_TFTP
+
+/* ENV setting */
+#define CONFIG_ENV_OVERWRITE	1
+/* Offset of env Flash sector relative to CONFIG_SYS_FLASH_BASE */
+
+/* Board Clock */
+#define CONFIG_SYS_CLK_FREQ	33333333
+#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_SYS_CLK_FREQ
+
+#endif	/* __MIGO_R_H */